Manual browser: traceroute(8)
|TRACEROUTE(8)||System Manager's Manual||TRACEROUTE(8)|
NAMEtraceroute - print the route packets take to network host
SYNOPSIStraceroute [ -aDFPIdlMnrvx ] [ -f first_ttl ]
] ] [ -A as_server ]
DESCRIPTIONThe Internet is a large and complex aggregation of network hardware, connected together by gateways. Tracking the route one's packets follow (or finding the miscreant gateway that's discarding your packets) can be difficult. Traceroute uses the IP protocol `time to live' field and attempts to elicit an ICMP TIME_EXCEEDED response from each gateway along the path to some host.
The only mandatory parameter is the destination host name or IP number. The default probe datagram length is 40 bytes, but this may be increased by specifying a packet length (in bytes) after the destination host name.
Other options are:
- Turn on AS# lookups for each hop encountered.
- Turn on AS# lookups and use the given server instead of the default.
- Turn on socket-level debugging.
- Dump the packet data to standard error before transmitting it.
- Set the initial time-to-live used in the first outgoing probe packet.
- Set the "don't fragment" bit.
- Specify a loose source route gateway (8 maximum).
- Specify a network interface to obtain the source IP address for outgoing probe packets. This is normally only useful on a multi-homed host. (See the -s flag for another way to do this.)
- Use ICMP ECHO instead of UDP datagrams.
- Display the ttl value of the returned packet. This is useful for checking for asymmetric routing.
- Set the max time-to-live (max number of hops) used in outgoing probe packets. The default value is taken from the net.inet.ip.ttl sysctl(3) variable.
- If found, show the MPLS Label and the Experimental (EXP) bit for the hop.
- Print hop addresses numerically rather than symbolically and numerically (saves a nameserver address-to-name lookup for each gateway found on the path).
- Set the base UDP port number used in probes (default is 33434). Traceroute hopes that nothing is listening on UDP ports base to base + nhops - 1 at the destination host (so an ICMP PORT_UNREACHABLE message will be returned to terminate the route tracing). If something is listening on a port in the default range, this option can be used to pick an unused port range.
- Set the "don't fragment" bit, and use the next hop mtu each time we get the "need fragmentation" error, thus probing the path MTU.
- Set the number of probe packets sent for each hop. By default, traceroute sends three probe packets.
- Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to ping a local host through an interface that has no route through it (e.g., after the interface was dropped by routed(8)).
- Use the following IP address (which usually is given as an IP number, not a hostname) as the source address in outgoing probe packets. On multi-homed hosts (those with more than one IP address), this option can be used to force the source address to be something other than the IP address of the interface the probe packet is sent on. If the IP address is not one of this machine's interface addresses, an error is returned and nothing is sent. (See the -i flag for another way to do this.)
- Set the type-of-service in probe packets to the following value (default zero). The value must be a decimal integer in the range 0 to 255. This option can be used to see if different types-of-service result in different paths. (If you are not running 4.4BSD, this may be academic since the normal network services like telnet and ftp don't let you control the TOS). Not all values of TOS are legal or meaningful - see the IP spec for definitions. Useful values are probably `-t 16' (low delay) and `-t 8' (high throughput).
- Verbose output. Received ICMP packets other than TIME_EXCEEDED and UNREACHABLEs are listed.
- Set the time (in seconds) to wait for a response to a probe (default 5 sec.).
- Toggle ip checksums. Normally, this prevents traceroute from calculating ip checksums. In some cases, the operating system can overwrite parts of the outgoing packet but not recalculate the checksum (so in some cases the default is to not calculate checksums and using -x causes them to be calculated). Note that checksums are usually required for the last hop when using ICMP ECHO probes (-I). So they are always calculated when using ICMP.
- Set the time (in milliseconds) to pause between probes (default 0). Some systems such as Solaris and routers such as Ciscos rate limit icmp messages. A good value to use with this this is 500 (e.g. 1/2 second).
This program attempts to trace the route an IP packet would follow to some internet host by launching UDP probe packets with a small ttl (time to live) then listening for an ICMP "time exceeded" reply from a gateway. We start our probes with a ttl of one and increase by one until we get an ICMP "port unreachable" (which means we got to "host") or hit a max (which defaults to 30 hops & can be changed with the -m flag). Three probes (change with -q flag) are sent at each ttl setting and a line is printed showing the ttl, address of the gateway and round trip time of each probe. If the probe answers come from different gateways, the address of each responding system will be printed. If there is no response within a 5 sec. timeout interval (changed with the -w flag), a "*" is printed for that probe.
We don't want the destination host to process the UDP probe packets so the destination port is set to an unlikely value (if some clod on the destination is using that value, it can be changed with the -p flag).
A sample use and output might be:
[yak 71]% traceroute nis.nsf.net.
traceroute to nis.nsf.net (22.214.171.124), 30 hops max, 38 byte packet
1 helios.ee.lbl.gov (126.96.36.199) 19 ms 19 ms 0 ms
2 lilac-dmc.Berkeley.EDU (188.8.131.52) 39 ms 39 ms 19 ms
3 lilac-dmc.Berkeley.EDU (184.108.40.206) 39 ms 39 ms 19 ms
4 ccngw-ner-cc.Berkeley.EDU (220.127.116.11) 39 ms 40 ms 39 ms
5 ccn-nerif22.Berkeley.EDU (18.104.22.168) 39 ms 39 ms 39 ms
6 22.214.171.124 (126.96.36.199) 40 ms 59 ms 59 ms
7 188.8.131.52 (184.108.40.206) 59 ms 59 ms 59 ms
8 220.127.116.11 (18.104.22.168) 99 ms 99 ms 80 ms
9 22.214.171.124 (126.96.36.199) 139 ms 239 ms 319 ms
10 188.8.131.52 (184.108.40.206) 220 ms 199 ms 199 ms
11 nic.merit.edu (220.127.116.11) 239 ms 239 ms 239 ms
A more interesting example is:
[yak 72]% traceroute allspice.lcs.mit.edu.
traceroute to allspice.lcs.mit.edu (18.104.22.168), 30 hops max
1 helios.ee.lbl.gov (22.214.171.124) 0 ms 0 ms 0 ms
2 lilac-dmc.Berkeley.EDU (126.96.36.199) 19 ms 19 ms 19 ms
3 lilac-dmc.Berkeley.EDU (188.8.131.52) 39 ms 19 ms 19 ms
4 ccngw-ner-cc.Berkeley.EDU (184.108.40.206) 19 ms 39 ms 39 ms
5 ccn-nerif22.Berkeley.EDU (220.127.116.11) 20 ms 39 ms 39 ms
6 18.104.22.168 (22.214.171.124) 59 ms 119 ms 39 ms
7 126.96.36.199 (188.8.131.52) 59 ms 59 ms 39 ms
8 184.108.40.206 (220.127.116.11) 80 ms 79 ms 99 ms
9 18.104.22.168 (22.214.171.124) 139 ms 139 ms 159 ms
10 126.96.36.199 (188.8.131.52) 199 ms 180 ms 300 ms
11 184.108.40.206 (220.127.116.11) 300 ms 239 ms 239 ms
12 * * *
13 18.104.22.168 (22.214.171.124) 259 ms 499 ms 279 ms
14 * * *
15 * * *
16 * * *
17 * * *
18 ALLSPICE.LCS.MIT.EDU (126.96.36.199) 339 ms 279 ms 279 ms
The silent gateway 12 in the above may be the result of a bug in the 4.BSD network code (and its derivatives): 4.x (x ≤ 3) sends an unreachable message using whatever ttl remains in the original datagram. Since, for gateways, the remaining ttl is zero, the ICMP "time exceeded" is guaranteed to not make it back to us. The behavior of this bug is slightly more interesting when it appears on the destination system:
1 helios.ee.lbl.gov (188.8.131.52) 0 ms 0 ms 0 ms
2 lilac-dmc.Berkeley.EDU (184.108.40.206) 39 ms 19 ms 39 ms
3 lilac-dmc.Berkeley.EDU (220.127.116.11) 19 ms 39 ms 19 ms
4 ccngw-ner-cc.Berkeley.EDU (18.104.22.168) 39 ms 40 ms 19 ms
5 ccn-nerif35.Berkeley.EDU (22.214.171.124) 39 ms 39 ms 39 ms
6 csgw.Berkeley.EDU (126.96.36.199) 39 ms 59 ms 39 ms
7 * * *
8 * * *
9 * * *
10 * * *
11 * * *
12 * * *
13 rip.Berkeley.EDU (188.8.131.52) 59 ms ! 39 ms ! 39 ms !
traceroute -g 10.3.0.5 184.108.40.206
traceroute -g 220.127.116.11 -g 10.3.0.5 18.104.22.168
This program is intended for use in network testing, measurement and management. It should be used primarily for manual fault isolation. Because of the load it could impose on the network, it is unwise to use traceroute during normal operations or from automated scripts.
SEE ALSOnetstat(1), ping(8)
AUTHORImplemented by Van Jacobson from a suggestion by Steve Deering. Debugged by a cast of thousands with particularly cogent suggestions or fixes from C. Philip Wood, Tim Seaver and Ken Adelman.
The current version is available via anonymous ftp:
BUGSPlease send bug reports to firstname.lastname@example.org.
The AS number capability reports information that may sometimes be inaccurate due to discrepancies between the contents of the routing database server and the current state of the Internet.
|21 September 2000||4.3 Berkeley Distribution|